MainPro Services Meets All NFPA Requirements

According to the standard for Health Care Facilities, NFPA-99 – “The Line Isolated Monitor (LIM) circuit shall be tested at intervals of not more than one month by activating the (LIM) test switch. For a LIM circuit with automated self-test and self-calibration capabilities, this test shall be performed at intervals of not more than 12 months.”

Appointments available
Timely inspections are crucial to a well run surgical arena

Quick Response Time…

Call today / Conveniently located in the tri-state area Ohio / Kentucky / Indiana Appointments available, with factory certified technicians available throughout the U.S.

Testing and Repair …

Meets all code requirements under NFPA 99, “Health Care Facilities” for six month and annual testing Certifications for new installations and existing units; trouble shooting and retro-fitting of all major systems, including: Square D, Bender, G.E.,
C.E.S. and Post Glover

In-Service Training …

Valuable for hospital personnel / Ensures all testing and Joint Commission
requirements are being met
How isolated power works, what to do in the case of an alarm and how to troubleshoot problems

Contact us today to order your MainPro Self-contained Isolated Power System

Testing

  • Testing can be completed on newly constructed or existing operating rooms
  • All testing is completed by Certified Technicians that comply with NFPA 99 Health Care Facilities and NFPA 70 National Electrical Code
  • Technicians are located nationwide for your service requirements
  • After completion of successful testing; a written certification is given to the hospital/facility to ensure the systems comply with required codes, good installation practices; and specifications.
  • Factory Start-Up Commissioning Test and Inspection
  • Annual Inspections

Certification

  • Certified testing of ungrounded isolated power systems and wiring per NFPA 99 Health Care Facilities and NFPA 70 National Electrical Code
  • Complete inspection of all receptacles for polarity
  • Verify Code requirements are being met and logged
  • MainPro Technicians will log voltage and millivolt readings criteria for acceptability for new construction or existing operating rooms
  • All Line Isolation Monitors will be tested and results of the readings will be properly documented
  • System Leakage and LIM Trip point readings will be compared to specifications of the Code requirements
  • Periodic testing and log instructions for future testing required by NFPA 99 will be documented for onsite maintenance personnel

Training

  • MainPro technicians train your onsite staff for LIM function, monitoring, maintenance, and testing logs.
  • Requirements by NFPA 99 will be included in the training handbook for references.
  • A training session is conducted with your hospital / facility medical and maintenance personnel on how to handle LIM equipment alarms.
  • The Field Test Reports and Maintenance log books will be reviewed.
  • This training session will also cover any questions or concerns about your Line Isolation Monitor.
  • A training video, designed to comply with the NFPA 99 requirements, is available on request.
  • After the training session, technical support is just a phone call away.

Repair

MainPro stocks many LIM & remotes for older systems. Contact us for assistance with your existing equipment.

Panel Upgrade

Panel Upgrade Is it time to replace an old analog LIM or remote? Whatever brand name you have; MainPro specializes in Retrofits. Retrofits are available to replace older LIMs and remotes that have become obsolete. The older panels with existing analog meters are no problem for the Sentry 5 digital remote. It will mount into the same existing space as the analog meter. With easy Retrofit Kits and self-select of voltage; one LIM does it all. The Sentry 5 LIM has taken the worries out of the installation.

Retrofits are available to replace any older LIM that has become obsolete.
Panel Mounted Remotes Without Meters
Wall Mounted Remotes Without Meters
Wall Mounted Remotes Without Meters Continued
Panel Mounted Remotes With Meters
Wall Mounted Remotes With Meters

Retrofits are available to replace any older LIM that has become obsolete.

The Sentry 5 digital LIM will mount into the same existing space as these meters

Bender LIM 2000plus

Square D Series D

Post Glover Mark IV

Sentry 5

We can replace any model of LIM

MainPro can also retrofit the LIMs below with the Sentry 5 LIM, Adapter Plate IPS-33 and wiring harness

Schneider Series 6

Bender LIM2010

Panel Mounted Remotes Without Meters

Change out the Bender MK2000 or Square D ORICA to the SQR-P panel mounted remote

SQR-P

Square D ORICA

Bender MK2000

Wall Mounted Remotes Without Meters

Retrofit to the SR-2 wall mounted remote from the Post Glover DRA-2, RA, or Square D IA-IC remote annunciators

SR-2

Post Glover DRA-2

RA

Square D IA-IC

Wall Mounted Remotes Without Meters Continued…

Retrofit to the SR-1 wall mounted remote from the Post Glover DRA-1, Schneider IG2000P, RA1, Bender MK2450 or MK2000P remote annunciators

SR-1

Post Glover DRA-1

Schneider IG2000P

RA1

Bender MK2000P

Bender MK2450

Bender MK2450

Panel Mounted Remotes With Meters

Change out the Square D ORIC-A5C or RA1 to the SQRM-P panel mounted remote

RA1

Square D ORIC-A5C

SQRM-P

Wall Mounted Remotes With Meters

Retrofit from the Post Glover DRA-1S, RA, Bender MK2000CBM or MK2450 MP-G2 to the SRM-2 wall mounted remote

Post Glover DRA-1S

RA

SRM-2

Bender MK2000CBM

Bender MK2450 MP-G2

Some hospitals still have the Square D M5-1A remote. Isolated Power Specialist can effortlessly retrofit to the SRM-6 wall mounted remote

Square D M5-1A

SRM-6

If you are keeping existing Square D and Bender LIMs, you can replace remotes without meters with the following remotes with voltage regulators:


ORICA

SQR-PVR

IA1C

SR-2VR

RA1 + IG2000P

SR-1VR

Some hospitals have Post Glover’s MKIII LIM with LED IDP Style or MKIII LIM IDP Style. MainPro can retrofit those with the Sentry 5 LIM on a stainless steel IDP adapter plate and plug

PG MKIII LIM with LED IDP Style

PG MKIII LIM IDP Style

Sentry 5 LIM on a stainless steel IDP adapter plate and plug